Project library / Seating

Seating / Build companion

Four-Board Bench

A slender hickory bench joins a rounded seat, two cutout leg panels, and a long stretcher with exposed wedged tenons.

Intermediate5 stages3-page source
AI finished-project concept for Four-Board Bench
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. An original study guide based on the supplied historical plan; not shop-tested. Use the privately owned source drawings for full-size patterns and complete cutting details.
Understand the project

What makes this build.

Fitting the wedged through tenons and interlocking stretcher laps requires accurate shoulder layout and careful control of wedge pressure.

Exposed through tenons connect legs to the seat.

The stretcher uses interlocking edge cross-laps.

The leg panels have semicircular bottom cutouts.

Points to resolve before building

  • Do not force oversize wedges into the tenons.
  • The source references a missing chapter for mortise technique; use a supported method you already understand.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Bandsaw or jigsaw
  • Backsaw
  • Drill
  • Chisels
  • Supported dado-cutting setup
  • Clamps

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Seat length53⅜ inSource p. 2
Seat width8¾ inSource p. 2
Underside housing depth¼ inSource p. 3

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Lay out the four pieces

Source pp. 2, 3

  1. Transfer the rounded seat ends, stretcher ends, and leg cutouts from the drawing. Mark the faces and grain before cutting so the two leg panels remain a matched pair. Keep a single centerline on each piece so the leg mortises and stretcher remain aligned when the seat is turned over.
Before moving onProfiles and joint locations agree on both legs.
Stage 2 of 5

Shape the visible curves

Source p. 3

  1. Saw outside the lines and refine the seat ends, the half-round stretcher ends, and the arches in the leg panels. Support the long seat during jigsaw work. Leave the joint-bearing edges square until the dry assembly is complete; rounding those edges early makes the fit harder to judge.
Before moving onCurves are fair and matched; no tear-out reaches a joint.
Stage 3 of 5

House the legs in the seat

Source p. 3

  1. Form the ¼-inch underside dadoes and the through mortises. Fit the leg tenons to these openings, leaving a little material proud to finish flush. Pare the mortise walls in small increments and test each labeled leg in its own opening before touching the other pair.
Before moving onEach leg seats fully without forcing its tenons.
Stage 4 of 5

Fit the stretcher laps

Source p. 3

  1. Cut the complementary edge notches in the legs and stretcher. Dry-fit the whole bench so the stretcher engages both leg panels and keeps them aligned. The source gives different notch depths in the legs and stretcher, so compare the assembled height instead of assuming equal half-depth cuts.
Before moving onThe seat is flat and the stretcher does not twist the legs.
Stage 5 of 5

Wedge and finish

Source p. 3

  1. Saw the tenon wedge kerfs and drill the specified small relief holes at their bases. Glue the fitted joints, install appropriately fitted wedges, then trim and smooth the proud ends after cure. Use the relief holes to terminate the kerfs cleanly, and stop if a wedge begins opening a crack beyond its intended slot.
Before moving onThe bench sits evenly and the wedged joints show no splits.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
4 board bench.pdf
Source length
3 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.