Project library / Seating

Seating / Build companion

Cedar Slat Bench

A straightforward backless cedar bench with four square posts and a gently scooped four-slat seat.

Beginner5 stages1-page source
AI finished-project concept for Cedar Slat Bench
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. Original reading guide based on the archived plan; not shop-tested. Confirm diagram dimensions against the private source before cutting.
Understand the project

What makes this build.

Straight screw-fastened construction is accessible, with optional curved supports.

Straight screw-fastened construction is accessible, with optional curved supports.

Four seat slats follow a gentle transverse scoop.

Lower skirt rails stiffen the square-post base.

Points to resolve before building

  • No tested seating capacity is supplied; inspect the joints before use.
  • Use exterior fasteners compatible with cedar.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw
  • Jigsaw or coping saw
  • Drill
  • Clamps
  • Square
  • Sander

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Bench47½ inches long × 16 inches deep × 17¾ inches highSource p. 1
LegsFour 4×4 posts cut 16⅜ inches longSource p. 1

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Prepare the cedar

Source p. 1

  1. Cut matching boards and posts, checking the actual dressed dimensions. Decide whether to keep a flat seat or use the shallow support curves shown. Choose the best faces for the seat and arrange their grain before drilling, since the four long slats define the finished appearance.
Before moving onAll repeated parts are equal and free of damaging splits.
Stage 2 of 5

Make the seat supports

Source p. 1

  1. Draw one smooth curve from the source layout and cut it as a template for the other supports. Sand the curves so all slats will bear consistently. Keep the template until the bench is assembled; a single high support can be checked against it if a slat rocks.
Before moving onThe six curved supports match.
Stage 3 of 5

Assemble the seat frame

Source p. 1

  1. Clamp the long rails and end supports square, then fit the four interior supports. Predrill the screws to protect the cedar ends. The outer support positions also locate the legs, so use a leg offcut as the source suggests to confirm their clearance.
Before moving onFrame is square and supports sit in one plane.
Stage 4 of 5

Attach slats and legs

Source p. 1

  1. Space the four seat slats evenly and fasten at the intended inner supports. With the seat upside down, hold each square post firmly in its corner and screw it in place. Fasten the slats only at the intended supports so later leg attachment has clear access and does not collide with existing screws.
Before moving onSeat gaps are even and legs remain square.
Stage 5 of 5

Add lower skirts and finish

Source p. 1

  1. Use equal spacer blocks to position the lower skirts, fitting ends before long sides. Ease all contact edges and inspect for rocking before applying finish. Use the same pair of spacer blocks at every corner so the skirt rails remain level without a chain of separate measurements.
Before moving onThe bench stands firmly with no protruding screws.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Simple Bench.pdf
Source length
1 pages
Attribution
Garden Gate No. 30, © August Home Publishing.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.