Project library / Boxes & small projects

Boxes & small projects / Build companion

One-Drawer Bandsaw Box

A single wooden block becomes a rounded little case and a matching pull-out drawer.

Intermediate5 stages2-page source
AI finished-project concept for One-Drawer Bandsaw Box
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. An original study guide based on the supplied historical plan; not shop-tested. Use the privately owned source drawings for full-size patterns and complete cutting details.
Understand the project

What makes this build.

Bandsaw drawer clearance and reattachment of the saved cheeks determine whether the small box works smoothly.

The drawer and case share the original block’s grain.

Saved cheek slices close the hollowed pieces.

Rounded corners suit narrow bandsaw cutting.

Points to resolve before building

  • The drawing is a method, not a dimensioned cutting plan.
  • Keep hands clear of the narrow blade and use a stable workpiece; do not force the curve.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Bandsaw with suitable narrow blade
  • Clamps
  • Sanding tools

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Source blade width¼ in; select to machine and curve limitsSource p. 2
Case cheek cut½ in from the outside faceSource p. 2

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Prepare a sound block

Source pp. 1, 2

  1. Glue compatible dry offcuts into a block or select a solid blank. Keep grain directions compatible and reject voids or loose knots in the intended cutting path. Prepare the blank within the machine’s supported cutting height and choose a shape whose internal curves suit the installed blade.
Before moving onThe cured block is solid and rests flat on the table.
Stage 2 of 5

Save the outer cheeks

Source p. 2

  1. Mark a continuous reference across the block and its outer slices. Saw off the two cheeks carefully and set them aside in their original orientation. Use the reference marks to preserve grain continuity and keep the slices flat while the center block is being worked.
Before moving onBoth cheek identities and mating faces remain clear.
Stage 3 of 5

Release the drawer blank

Source p. 2

  1. Draw a rounded drawer outline on the center block. Cut on the waste side, using curves broad enough for the selected blade rather than forcing tight turns. Plan the entry cut so it can be closed cleanly during reassembly, and keep the blade moving without twisting the blank.
Before moving onThe drawer blank separates without damaged corners.
Stage 4 of 5

Hollow the drawer

Source p. 2

  1. Slice off and label the drawer cheeks, then cut out its interior waste. Smooth the interior before gluing the saved cheeks back to the drawer and case. Sand the cavity before closing it with its cheeks, since those interior surfaces become difficult to reach after glue-up.
Before moving onThe hollow drawer and case glue lines close cleanly.
Stage 5 of 5

Tune the sliding fit

Source p. 2

  1. Sand the drawer gradually, checking its travel repeatedly. Ease the case edges and finish without building a thick film on the sliding surfaces. Remove only a little material from each contact surface, keeping the drawer square enough that it does not wedge when pulled.
Before moving onThe drawer opens freely without excessive looseness.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Bandsaw Box.pdf
Source length
2 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.