Project library / Storage & cabinets

Storage & cabinets / Build companion

Stacking Barrister Bookcase

Modular cherry cases stack over a shaped base and close with glass doors that lift and slide inward.

Advanced6 stages6-page source
AI finished-project concept for Stacking Barrister Bookcase
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. An original study guide based on the supplied historical plan; not shop-tested. Use the privately owned source drawings for full-size patterns and complete cutting details.
Understand the project

What makes this build.

Accurate indexing dowels and homemade lift-and-slide door grooves are essential for interchangeable stackable cases.

Lift-and-slide doors use wooden pins in stopped grooves.

A case top also serves the unit above.

Indexing dowels register the stack.

Points to resolve before building

  • Replace the source’s unsafe stopped table-saw plunge method with a guarded supported routing method.
  • Stacking dowels do not provide anti-tip anchorage.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Router table with guards and coping support
  • Drill press
  • Doweling jig
  • Biscuit joiner
  • Saw
  • Clamps

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Case top or bottom¾ × 12⅝ × 34¼ inSource p. 6
Tall side panels¾ × 12 × 13¼ inSource p. 6
Door frame width1¼ inSource p. 4

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 6

Choose the modular arrangement

Source p. 3

  1. Decide how many cases and which source heights to build. Prepare panels to a common thickness so every unit can mate with the others. Keep tall and short unit parts in separate labeled stacks while preserving the common width and depth that make the system modular.
Before moving onA complete stack layout and matched parts list are ready.
Stage 2 of 6

Machine the case sides

Source p. 3

  1. Cut back rabbets and the stopped door-slide grooves, keeping left and right parts clearly labeled. Use test pins to tune the groove clearance. The slide grooves stop short of the front, so use mirrored stop settings for left and right case sides.
Before moving onDoor pins slide smoothly without excessive play.
Stage 3 of 6

Drill the indexing system

Source pp. 3, 4

  1. Use stops and a doweling jig to match the holes in case bottoms and side tops. Dry-stack the empty cases before gluing the biscuit joints. Drill matching top and bottom references from the same face, because the front and rear indexing holes are not equally offset.
Before moving onEach case seats on the dowels without rocking.
Stage 4 of 6

Make the base and doors

Source pp. 4, 5

  1. Assemble the shaped base and cope-and-stick door frames. Form removable-glass rabbets with a safely supported router and chisel method; do not lower parts onto a running table-saw blade as the old text suggests. Use a coping support for the narrow door rails and fit the removable glass stops after the frame is square.
Before moving onFrames are square and the glass recess is continuous.
Stage 5 of 6

Fit door motion

Source p. 5

  1. Fit the door-edge pins and the separate support pins to the source detail. Check side and bottom gaps and the extra top clearance throughout lifting and sliding. The upper clearance is larger than the side and bottom gaps to permit the door to pivot before sliding inward.
Before moving onEvery door opens, parks and closes without catching.
Stage 6 of 6

Finish and secure the stack

Source pp. 5, 6

  1. Finish the parts, fit glass with removable stops, and screw on the backs. Level the base and add suitable anti-tip anchoring for the completed stack. Install the removable backs after finishing and confirm that the anti-tip arrangement permits safe access to the modular joints.
Before moving onDoors operate after the cabinet is leveled and anchored.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Barrister Bookcase.pdf
Source length
6 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.