Project library / Storage & cabinets

Storage & cabinets / Build companion

Breadboard-Lid Blanket Chest

A plain solid-wood chest has a breadboard-ended hinged lid, low base trim and side carrying handles.

Intermediate5 stages3-page source
AI finished-project concept for Breadboard-Lid Blanket Chest
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. An original study guide based on the supplied historical plan; not shop-tested. Use the privately owned source drawings for full-size patterns and complete cutting details.
Understand the project

What makes this build.

Breadboard lid movement and weight-matched lid supports are the main concerns beyond a square paneled chest.

Breadboard ends cap the solid-wood lid.

A piano hinge runs along most of the back edge.

Simple low base molding wraps the front and sides.

Points to resolve before building

  • Heavy lids can crush fingers; choose support hardware by measured lid weight.
  • This is storage furniture, not a child enclosure or seat; no load rating is supplied.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw
  • Router
  • Drill
  • Clamps
  • Plane

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Front and back panels34 × 17¼ inSource p. 1
Side panels19 × 17¼ inSource p. 1
Lid overall drawing35½ × 20¼ inSource p. 2

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Prepare the case panels

Source p. 1

  1. Glue up the front, back and sides oversize, then cut their joints and final dimensions from the drawing. Keep all parts at a consistent thickness. Dry-fit the box before trimming its top edge so any small joint mismatch can be corrected without reducing one panel unnecessarily.
Before moving onThe dry box is square and its top edges lie in one plane.
Stage 2 of 5

Fit the base and floor

Source p. 1

  1. Make the three-sided base trim and fit the inner floor-support strips. Cut the plywood floor to the actual opening and secure it on the supports. The source omits rear base trim, so check the rear floor support independently instead of assuming trim supports every edge.
Before moving onThe floor is continuously supported at its edges.
Stage 3 of 5

Build the moving lid

Source p. 2

  1. Fit the central panel and breadboard ends. Glue only the limited front portion indicated and use elongated rear and center dowel holes to allow the solid panel to move. The solid center panel’s grain direction governs which holes are elongated; a plywood substitute changes that movement behavior.
Before moving onBreadboard joints retain cross-grain movement.
Stage 4 of 5

Fit hinge and supports

Source p. 3

  1. Install the piano hinge with predrilled holes, then select and install lid supports to the lid’s actual weight and manufacturer instructions. Do not rely on an unsupported lid during fitting. The source recommends selecting support strength by lid weight and using more than one support if the hardware requires it.
Before moving onThe lid stays controlled throughout its travel.
Stage 5 of 5

Add handles and finish

Source p. 3

  1. Fit the side handles, remove hardware for finishing and reinstall after cure. Check lid clearances and finger-pinch locations before use. Place handles consistently on both sides and verify that their screws do not create sharp interior projections.
Before moving onThe finished lid cannot fall unexpectedly.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Blanket chest.pdf
Source length
3 pages
Attribution
Binky’s Woodworking; scanned plan revised December 2001, signed Barry.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.