Project library / Storage & cabinets

Storage & cabinets / Build companion

Four-Peg Bathroom Shelf

A wall shelf combines shaped end panels with four upward-tilted wooden towel pegs.

Beginner5 stages3-page source
AI finished-project concept for Four-Peg Bathroom Shelf
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. An original study guide based on the supplied historical plan; not shop-tested. Use the privately owned source drawings for full-size patterns and complete cutting details.
Understand the project

What makes this build.

Matching curved ends and drilling four consistently angled peg holes are the main fitting tasks.

Four angled pegs sit below the shelf.

Tall curved end panels retain folded items.

A broad back provides a wall-fixing surface.

Points to resolve before building

  • The source gives no wall load capacity; match anchors to the substrate and intended contents.
  • Keep screw pilot holes clear of thin panel edges.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw
  • Jigsaw
  • Drill
  • Plane or spokeshave
  • Sander

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Shelf700 × 125 mmSource p. 2
Peg size18 mm diameter × 75 mmSource p. 2

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Transfer the end shape

Source pp. 2, 3

  1. Use the source profile for two matching ends and mark their orientation. Cut the shelf and back to the listed widths and lengths. Mark the rear edge of each end panel before shaping so the two pieces remain handed correctly around the shelf.
Before moving onThe end panels form a matched pair.
Stage 2 of 5

Shape and ease the pieces

Source p. 3

  1. Saw the end curves and soften the exposed edges. Retain flat mating surfaces where the ends meet the shelf and back. Use the same template to check the pair after sanding, because uneven end heights are conspicuous once the shelf is wall-mounted.
Before moving onCurves match and joints retain full contact.
Stage 3 of 5

Fasten the shelf frame

Source p. 3

  1. Predrill the back and ends for the countersunk screws. Assemble the shelf to the back first, then fit the end panels without splitting their edges. Countersink only enough to bury the screw heads; excessive countersinking reduces the holding material in thin board edges.
Before moving onThe shelf is square to its back.
Stage 4 of 5

Fit the angled pegs

Source p. 3

  1. Mark the four holes from the source spacing and drill them at a consistent slight upward angle. Use a secure angled drilling guide rather than an unsupported freehand setup. Test the drilling angle with a scrap backboard and dowel before drilling the four visible peg positions.
Before moving onAll pegs project equally and tilt upward together.
Stage 5 of 5

Finish and mount

Source p. 3

  1. Glue the pegs, sand and apply a bathroom-suitable coating. Fasten through the upper back using fixings appropriate to the wall construction. Leave space for the hanging towels below the pegs and place the upper wall fasteners where the back has solid support.
Before moving onThe shelf is firmly mounted and the pegs cannot twist.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Bathroom Shelf.pdf
Source length
3 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.