Project library / Storage & cabinets

Storage & cabinets / Build companion

Two-Shelf Towel Rack

A wall rack combines two low shelves with a towel rod held between curved side panels.

Intermediate5 stages2-page source
AI finished-project concept for Two-Shelf Towel Rack
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. An original study guide based on the supplied historical plan; not shop-tested. Use the privately owned source drawings for full-size patterns and complete cutting details.
Understand the project

What makes this build.

The shelf dadoes and blind rod holes must line up across two shaped side panels without breaking through their outer faces.

Two shelves are housed in side-panel dadoes.

The towel rod fits blind holes in the shaped sides.

The supplied illustration shows open space above the lower shelves.

Points to resolve before building

  • Complete cutting sizes are not legible in the extracted text; retain the source drawing.
  • Wall fixing details require separate selection.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw
  • Bandsaw or jigsaw
  • Guided router or dado setup
  • Drill
  • Clamps

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Use the original drawing.

The source does not provide a complete, confidently readable set of dimensions here. Confirm the original drawing and develop a measured parts list before cutting.

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Match the side blanks

Source pp. 1, 2

  1. Square and cut the two sides and mark their inward faces. Transfer the shelf and rod locations from the diagram rather than guessing spacing. Keep the full-height side blanks paired during marking so shelves and rods remain parallel after assembly.
Before moving onBoth sides carry matching joint marks.
Stage 2 of 5

House the shelves

Source p. 2

  1. Cut matching dadoes for the shelves while the side blanks remain rectangular. Test the fit with actual shelf stock. A trial dado in scrap confirms both groove width and depth before the visible side panels are machined.
Before moving onThe shelves enter without forcing or loose gaps.
Stage 3 of 5

Cut the curved ends

Source p. 2

  1. Lay out the straight and curved portions of each side profile. Saw outside the lines and sand the pair to a matching shape. Leave enough straight reference edge for the remaining hole layout and remove saw marks without rounding joint-bearing surfaces.
Before moving onThe end curves are smooth and symmetrical.
Stage 4 of 5

Drill for the rod

Source p. 2

  1. Mark paired blind holes and set a positive drilling depth stop. Fit the dowel without breaking through the visible outside faces. Test the rod with both side panels dry-clamped around the shelves so its final length does not prevent the joints closing.
Before moving onThe rod seats fully in both side panels.
Stage 5 of 5

Glue and mount

Source p. 2

  1. Sand inside surfaces, dry-fit all shelves, backs and rod, then glue and clamp square. Finish for bathroom exposure and add wall attachment suitable for the rack and towels. Install the chosen wall hangers into substantial areas of the rack rather than relying on thin shelf backs alone.
Before moving onShelves are level and the mounted rack cannot pull away.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Bathroom Towel Rack.pdf
Source length
2 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.