Project library / Tables & desks

Tables & desks / Build companion

Hand-Tool Side Table

A small pine table uses square legs, mortise-and-tenon aprons and a solid board top.

Intermediate5 stages6-page source
AI finished-project concept for Hand-Tool Side Table
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. An original study guide based on the supplied historical plan; not shop-tested. Use the privately owned source drawings for full-size patterns and complete cutting details.
Understand the project

What makes this build.

Hand-cut mortises and tenons, flat panel glue-up and movement-friendly top attachment make this a useful small joinery exercise.

Hand-cut mortise-and-tenon apron joints.

Small solid-wood top with overhang.

Optional taper and apron curves are separate variations.

Points to resolve before building

  • Use the drawing for leg length and joint positions; the guide selects the plain square-leg version.
  • Do not rigidly screw a wide solid top across its grain.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Handsaw
  • Backsaw
  • Jack plane
  • ¼-inch mortise chisel or brace and chisel
  • Square
  • Clamps

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Top drawing16 × 14 inSource p. 1
Leg stock1¾ in squareSource p. 5
Mortises¼ in wide × 1 in deepSource p. 5

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Prepare the leg stock

Source p. 5

  1. Plane four square leg blanks, gluing thinner stock if necessary. Mark the two inward-facing joint surfaces on each leg. If laminating legs, remove squeezed-out glue and plane the cured blanks before setting the marking gauge for the rail mortises.
Before moving onAll legs share the same section and reference faces.
Stage 2 of 5

Cut the paired mortises

Source p. 5

  1. Lay out the rail mortises from one marking-gauge setting. Chop them or bore and pare them to the source depth. Work from the same reference face on adjacent mortises so the aprons meet consistently at each inside corner.
Before moving onMortises align and remain square to the leg faces.
Stage 3 of 5

Fit the apron tenons

Source p. 5

  1. Knife the shoulders and saw the tenon cheeks. Fit the straight apron version first; cut any optional curved lower edge only after the joints fit. Pare the tenon cheeks to fit rather than enlarging every mortise, keeping the outer shoulder lines clean and continuous.
Before moving onShoulders close without forcing the legs apart.
Stage 4 of 5

Glue the base square

Source p. 5

  1. Dry-assemble and compare diagonals, then glue the fitted joints. Keep the upper rail and leg surfaces in one plane. Compare both diagonals and sight across the upper edges; equal diagonals alone do not rule out a twisted base.
Before moving onThe base sits without rocking and is untwisted.
Stage 5 of 5

Glue and fit the top

Source p. 6

  1. Joint the top boards, glue them into an oversize panel and plane it flat after cure. Cut the panel to size, ease its edges and attach with allowance for cross-grain movement. When edge-jointing by hand, pair mating edges back-to-back so small planing-angle errors cancel when the boards are opened out.
Before moving onThe top is secure but can move seasonally.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Basic Table.pdf
Source length
6 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.