Project library / Tables & desks

Tables & desks / Build companion

Open-Shelf Bedside Table

A small table has rounded square legs, a solid top and a low shelf captured in leg notches.

Intermediate5 stages3-page source
AI finished-project concept for Open-Shelf Bedside Table
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. An original study guide based on the supplied historical plan; not shop-tested. Use the privately owned source drawings for full-size patterns and complete cutting details.
Understand the project

What makes this build.

The lower shelf must fit four leg housings at once, and the top attachment must accommodate wood movement.

The low shelf is captured by notches in all four legs.

Laminated legs receive rounded vertical edges.

No drawer interrupts the open front.

Points to resolve before building

  • Replace historical drywall screws with suitable wood screws.
  • The full drawing is needed for panel dimensions; retain seasonal movement at the top.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw
  • Plane
  • Router
  • Doweling or biscuit jig
  • Drill
  • Clamps

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Finished legs1½ × 1½ × 18¾ inSource p. 3
Shelf corner notches¾ × ¾ inSource p. 3
Long and short rails12½ in and 6½ in long, 2 in wideSource p. 3

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Glue the two panels

Source p. 2

  1. Joint and glue oversize panels for the top and shelf. Flatten them after cure and cut them to the drawing sizes. Keep the top and shelf separately labeled because only the top receives the decorative edge treatment.
Before moving onBoth panels are flat with sound glue lines.
Stage 2 of 5

Prepare the rounded legs

Source p. 3

  1. Laminate the paired leg strips, then machine the four blanks to equal length and section. Rout the indicated edge roundovers before final sanding. Cut all leg lengths from the same stop setting, then check them on a flat surface before routing the housings.
Before moving onThe four legs match and retain square joint references.
Stage 3 of 5

Fit the low shelf

Source p. 3

  1. Cut the shelf corner notches and matching adjacent-face leg housings. Dry-fit all four legs around the shelf. Cut the paired adjacent-face housings from consistent references so the shelf does not tilt across the narrow table base.
Before moving onThe shelf sits level and does not spread the legs.
Stage 4 of 5

Join the apron rails

Source p. 3

  1. Fit dowel or biscuit joints for the narrow rails. Drill the top-attachment clearance system and assemble with the shelf already captured. Complete a full dry assembly with the shelf installed; it cannot be added after all four leg-to-rail joints are closed.
Before moving onThe base is square with the shelf enclosed.
Stage 5 of 5

Attach the top

Source p. 3

  1. Ease the top edge, finish the parts and attach with suitable wood screws through movement-friendly holes. Use controlled slots instead of wobbling a drill to enlarge holes. Center the screws within the movement slots at assembly so the top has room to expand and contract in either direction.
Before moving onThe top is centered, secure and free to move across its grain.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Bedside Table.pdf
Source length
3 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.