Project library / Tables & desks

Tables & desks / Build companion

Wing-Leg Cherry Table

A refined cherry end table has curved tapered legs, a fitted lower shelf and a raised-center top.

Advanced6 stages5-page source
AI finished-project concept for Wing-Leg Cherry Table
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. An original study guide based on the supplied historical plan; not shop-tested. Use the privately owned source drawings for full-size patterns and complete cutting details.
Understand the project

What makes this build.

Curved wing-leg units, individually scribed shelf notches and a shaped moving top make this an advanced fitted table.

Wing laminations create broad curved upper leg corners.

The lower shelf is individually scribed to each leg.

The top has a raised center panel and beveled underside.

Points to resolve before building

  • Cut shelf and top to the assembled frame, not guessed final dimensions.
  • Use a supported bevel setup appropriate to the saw’s actual tilt direction.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw
  • Bandsaw
  • Chisels
  • Plane
  • Spokeshave
  • Drill
  • Clamps

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Shelf reference height13¼ in above the floorSource p. 4
Alternative square leg blank1¾ in square × 24⅞ in long, with added wingsSource p. 2

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 6

Laminate the corner units

Source p. 3

  1. Glue the wing pieces to the leg blanks with flush upper ends. Keep the corner units square until the apron mortises are located. Choose matching grain at the glued wings so the expanded corner appears coherent after its final curve is cut.
Before moving onWing joints close and corner references remain true.
Stage 2 of 6

Fit the apron joints

Source p. 3

  1. Cut the apron tenons and transfer their positions to the leg units. Fit the mortises before shaping away the leg waste. Keep the apron tops flush to the leg units during marking, since they establish the top attachment plane.
Before moving onThe dry base is square and its shoulders close.
Stage 3 of 6

Refine the curved legs

Source pp. 3, 4

  1. Mark both outer faces from the pattern and rough-cut with adequate support. Plane and spokeshave to the final flowing taper. Support the leg on the saw table with temporary waste where necessary so the second profile cut is not made on a rocking blank.
Before moving onAll four leg curves agree and retain sufficient joint material.
Stage 4 of 6

Scribe the lower shelf

Source p. 4

  1. Measure the dry frame at the source shelf height, then edge the plywood shelf. Label each corner and transfer its actual shape to the matching leg notch. The source adds a small fitting allowance before edging the shelf, then uses each labeled corner to mark its own notch.
Before moving onThe shelf fits all four notches without spreading the legs.
Stage 5 of 6

Glue the base and shape the top

Source pp. 4, 5

  1. Assemble the end frames, then join them around the fitted shelf. Size the solid top to the completed frame and form its raised center and lower bevel. Center the upside-down base on the top blank to transfer the corner positions before cutting the underside bevel.
Before moving onThe top profile aligns with the leg-and-wing corners.
Stage 6 of 6

Attach with movement allowance

Source p. 5

  1. Make slotted blocks with slots running across the top grain. Attach the top using washers and screws that retain it without locking seasonal movement. Leave the top screws snug enough to retain the washers without preventing them from sliding in the blocks.
Before moving onThe top is centered and its fasteners can travel in the slots.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Cherry End Table.pdf
Source length
5 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.