Project library / Storage & cabinets

Storage & cabinets / Build companion

Oak Media Bookcase

A tall oak-faced cabinet combines open adjustable shelves with a wider media bay and a lower panel door.

Intermediate6 stages6-page source
AI finished-project concept for Oak Media Bookcase
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. An original study guide based on the supplied historical plan; not shop-tested. Use the privately owned source drawings for full-size patterns and complete cutting details.
Understand the project

What makes this build.

Multiple unequal compartments, a large face frame and layered molding make accurate carcass layout more important than any single cut.

Asymmetric bays distinguish this media cabinet from a plain bookcase.

Solid-oak nosings cover plywood shelf edges.

An optional lower panel door conceals storage.

Points to resolve before building

  • The text refers to a cutting list not recovered here; full source drawings are needed for case dimensions.
  • An extended heavy media shelf increases tipping risk; use rated hardware and suitable anchoring.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw
  • Guided router
  • Drill
  • Doweling or biscuit jig
  • Clamps

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Initial plywood strip width15¾ inSource p. 2
Shelf-pin spacing2 in verticallySource p. 3

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 6

Map the unequal bays

Source pp. 1, 2

  1. Study the source arrangement of wide media compartments and narrow book shelves. Mark every fixed shelf and divider before cutting the plywood. Identify which shelves are fixed and which are adjustable before routing, because their joints and support requirements differ.
Before moving onThe bay layout is complete and part orientations are clear.
Stage 2 of 6

Cut the housing joints

Source pp. 2, 3

  1. Cut the panel dadoes and top dado-rabbet joints to the actual plywood thickness. Use supported setups and preserve the thin face veneers. The shelf divider with joints on both faces uses shallower housings, so do not repeat the ordinary dado depth automatically.
Before moving onAll fixed panels dry-fit squarely.
Stage 3 of 6

Drill adjustable shelf rows

Source pp. 3, 4

  1. Drill matching support holes in the right side and internal dividers with a jig. Keep the adjustable shelves out of the case glue-up. The source locates pin rows from front and rear references; keep those references consistent across both dividers and the case side.
Before moving onCorresponding shelf holes are level across each bay.
Stage 4 of 6

Assemble and face the cabinet

Source p. 4

  1. Prefinish accessible faces while leaving glue areas bare. Assemble the case with help, then fit the doweled or biscuited outer oak face frame. Keep finish away from housed edges and face-frame glue surfaces so the glue bonds to wood rather than cured coating.
Before moving onThe tall case remains square with the frame attached.
Stage 5 of 6

Add shelf edges and crown

Source p. 5

  1. Shape moldings while stock is wide enough to handle safely, or use purchased equivalents. Fit the shelf nosings and mitered crown to the completed carcass. Measure shelf nosings after the outer face frame is installed, and fit the media-shelf side nosings separately.
Before moving onMoldings close at corners without obstructing shelves.
Stage 6 of 6

Fit the lower door and equipment

Source pp. 5, 6

  1. Make the framed plywood-panel door and fit hinges. Use any sliding equipment shelf only with hardware rated for its actual load and secure the cabinet against tipping. Test the optional moving shelf with the actual hardware travel and expected equipment envelope before loading it.
Before moving onDoors and shelves operate without compromising stability.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Book Case 1.pdf
Source length
6 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.