Project library / Boxes & small projects

Boxes & small projects / Build companion

Sliding-Lid Candlebox

A dovetailed rectangular box closes with a beveled sliding lid and a carved recessed finger pull.

Advanced5 stages4-page source
AI finished-project concept for Sliding-Lid Candlebox
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. An original study guide based on the supplied historical plan; not shop-tested. Use the privately owned source drawings for full-size patterns and complete cutting details.
Understand the project

What makes this build.

Through dovetails, thin sliding-panel bevels and the carved pull require precise hand-tool fitting and controlled assembly.

Through dovetails remain visible on the ends.

The beveled lid runs in grooves on three sides.

A carved inset pull replaces external hardware.

Points to resolve before building

  • The source refers elsewhere for dovetail instruction; this guide is not a full dovetail lesson.
  • Follow product directions for finish and oily-rag disposal rather than mixing the historical recipe casually.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Dovetail saw
  • Chisels
  • Plane
  • Marking gauge
  • Router or plow plane
  • Clamps

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
SidesTwo at ½ × 7 × 14 inSource p. 4
Lid½ × 8 × 13¾ inSource p. 4
Bottom½ × 8 × 13½ inSource p. 4

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Cut the panel grooves

Source p. 2

  1. Prepare the parts to consistent thickness and cut the top and bottom grooves from the drawing. Keep the shortened entry end distinct from the full-height end. Label the lid-entry end clearly so its reduced height is not confused with the end that carries the closing groove.
Before moving onGrooves align around the box and the lid has an entry opening.
Stage 2 of 5

Fit the corner dovetails

Source pp. 2, 4

  1. Lay out and cut through dovetails at each corner. Leave only enough proud material for final flush trimming. Check the tails and pins with the grooved panels present in the dry fit, since the grooves can remove material near a corner joint.
Before moving onThe dry case is square with closed shoulders.
Stage 3 of 5

Bevel the sliding panels

Source p. 2

  1. Plane the lid and bottom bevels to fit their grooves, working end grain before long grain. Check the lid through its full travel. Keep the two long bevels even so the lid stays level in its tracks instead of tilting and binding.
Before moving onThe lid slides without rocking or binding.
Stage 4 of 5

Carve the finger pull

Source pp. 2, 4

  1. Mark the recessed pull near the exposed end. Use controlled chisel and gouge cuts with the lid securely held, then smooth or lightly texture the depression. Work with the grain where possible and take small cuts at the pull’s edge to avoid breaking away the thin raised lip.
Before moving onThe pull is comfortable and has no fragile lip.
Stage 5 of 5

Assemble and finish

Source pp. 2, 4

  1. Glue the dovetails around the floating bottom and fit the groove-end plugs. Trim flush and apply a suitable finish without coating the running surfaces too heavily. Trim the groove plugs to match the surrounding grain direction and recheck the lid fit after the finish dries.
Before moving onThe bottom can move and the lid still slides freely.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Candle box.pdf
Source length
4 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.