Project library / Boxes & small projects

Boxes & small projects / Build companion

Three-Arm Wooden Candelabra

Three curved wooden arms join a triangular center post to make a radial candle display.

Intermediate5 stages3-page source
AI finished-project concept for Three-Arm Wooden Candelabra
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. An original study guide based on the supplied historical plan; not shop-tested. Use the privately owned source drawings for full-size patterns and complete cutting details.
Understand the project

What makes this build.

Three radial dowel-jointed arms must align around a triangular post while their feet and candle platforms remain level.

Three arms radiate around a triangular post.

Each arm combines a curved web and a thicker candle-bearing end.

The arm bottoms act as three stable feet.

Points to resolve before building

  • The historic bare-wood candle holes are not a fire-safe holder system; use flameless candles.
  • Do not over-enlarge the narrow top recesses.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Bandsaw
  • Drill
  • Plane
  • Clamps
  • Sander

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Arm blanks¾ × 4¾ × 11 inSource p. 3
Center post2¼-inch triangular stock, 9 in longSource p. 3
Source candle recess⅞ in diameter × 1¼ in deepSource p. 2

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Make the triangular center

Source pp. 2, 3

  1. Prepare the post from solid or laminated stock and form three equal faces. Ease the sharp vertical corners without changing the arm contact surfaces. Use a sample cross-section to verify the triangular geometry before cutting the full post from the selected stock.
Before moving onAll three faces are straight and equally spaced.
Stage 2 of 5

Shape the matching arms

Source pp. 2, 3

  1. Transfer the curved arm pattern and saw three matching pieces. Refine the long concave edges with supported sanding. Leave the thicker outer ends intact until the side laminations have been fitted and the candle recess location is confirmed.
Before moving onArm silhouettes match when stacked.
Stage 3 of 5

Drill the dowel pattern

Source pp. 2, 3

  1. Mark the three dowel positions on each arm and the corresponding post face. Drill to a controlled depth using a fixture that supports the angled post. Use a depth stop because the angled post leaves less material behind some drilling directions than a square block would.
Before moving onEvery arm fits its post face fully.
Stage 4 of 5

Laminate the candle ends

Source p. 2

  1. Glue the side strips to the arms and drill the top recesses after cure. Adapt the recess fit to flameless taper candles rather than placing an open flame directly above wood. The recess edge can be lightly chamfered after boring, but retain enough wall thickness to support the selected flameless taper.
Before moving onRecesses are centered and do not split the top ends.
Stage 5 of 5

Assemble the radial form

Source p. 2

  1. Glue the arms around the center post and check that all three feet share a plane. Finish and add felt pads under the feet. Clamp with protective cauls and compare all foot contacts on a flat board before the glue sets.
Before moving onThe candelabra stands evenly without rocking.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Candlelabra.pdf
Source length
3 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.