Project library / Storage & cabinets

Storage & cabinets / Build companion

Angled Cassette Rack

Two sloping shelves and horizontal retaining dowels organize cassette cases between plain side panels.

Intermediate5 stages2-page source
AI finished-project concept for Angled Cassette Rack
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. An original study guide based on the supplied historical plan; not shop-tested. Use the privately owned source drawings for full-size patterns and complete cutting details.
Understand the project

What makes this build.

The matching 45-degree shelf dadoes and retaining-rod locations must work together to hold cassette cases at the intended angle.

Two shelves slope at 45 degrees.

Round dowels retain the case fronts.

Plain tall side panels house all connections.

Points to resolve before building

  • Do not use a rip fence as a trapping stop when crosscutting.
  • The drawing, not the generic material prose, controls rod placement.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw
  • Guided router
  • Drill
  • Clamps
  • Sander

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Shelf angle45°Source p. 2
Illustrated side height18½ inSource p. 2

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Size around cassette cases

Source pp. 1, 2

  1. Use the source drawing and actual cases to confirm shelf depth and clearance. Cut the side panels first, keeping the shelf blanks long until their bevels are established. Use a sample case to check both the shelf support and the amount exposed above the rods for easy removal.
Before moving onA sample case fits the planned section.
Stage 2 of 5

Cut diagonal housings

Source p. 2

  1. Mark matching 45-degree dadoes on the inside faces. Use a clamped guide and test the fit with shelf stock. Keep the guide clamped against a stable side-panel reference so the diagonal cut cannot creep during successive passes.
Before moving onBoth shelves sit at the same angle in each side.
Stage 3 of 5

Bevel the shelves

Source p. 2

  1. Cut the shelf bevels to match the housing geometry and check their final span. Keep waste clear of the blade and use a supported angle-cutting setup. Test the mating bevel with the dadoed sides before cutting the second shelf to final length.
Before moving onShelf edges seat fully without opening the side joints.
Stage 4 of 5

Drill retaining-rod holes

Source p. 2

  1. Transfer the rod positions from the sectional drawing and drill paired blind holes with a depth stop. Dry-fit all rods and shelves together. Use a mechanical depth stop where possible, leaving enough wood behind every blind hole to avoid visible break-through.
Before moving onRods clear the stored cases and retain them at the front.
Stage 5 of 5

Glue the rack

Source p. 2

  1. Sand accessible surfaces, then glue and clamp the rack square. Apply a thin finish and recheck the fit of the actual cases. Wipe glue from the narrow rod joints before it hardens, then test access with cases in both levels at once.
Before moving onCases can be removed without catching on rods.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Cassette Holder.pdf
Source length
2 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.