Project library / Storage & cabinets

Storage & cabinets / Build companion

Freestanding Clothes Rack

A wide timber clothes rack has a top shelf, a full hanging rail and a second half-width rail.

Intermediate5 stages3-page source
AI finished-project concept for Freestanding Clothes Rack
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. An original study guide based on the supplied historical plan; not shop-tested. Use the privately owned source drawings for full-size patterns and complete cutting details.
Understand the project

What makes this build.

The long dowel spans, half-lapped feet and diagonal braces must align to keep the freestanding rack stable under uneven garment loads.

Three posts divide a wide open frame.

A lower rail doubles hanging capacity on one side.

Long feet and diagonal braces stabilize the freestanding form.

Points to resolve before building

  • A loaded high shelf can overturn the rack; no capacity is stated.
  • Do not substitute shallow screws into particleboard edges for the specified supported connections.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw
  • Miter box
  • Drill
  • Chisels
  • Clamps

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Shelf2100 × 400 × 19 mmSource p. 2
PostsThree at 1975 mmSource p. 2
FeetTwo at 900 mmSource p. 2
Hanging rails25 mm diameterSource p. 2

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Build the foot joints

Source p. 3

  1. Cut half-laps where the long lower rail crosses the two feet. Predrill and fasten these joints into the end posts as drawn. The posts attach through the foot joints, so drill their pilot holes squarely while the base is clamped in its final alignment.
Before moving onThe base sits flat and the posts are upright.
Stage 2 of 5

Fit the diagonal braces

Source p. 3

  1. Cut the paired foot braces with the source end angles and notches. Fit the inner braces and center post so the wide frame resists racking. The outer brace notches wrap around the posts and feet; test the bearing surfaces before driving the retaining screws.
Before moving onAll braces bear fully and the frame is square.
Stage 3 of 5

Prepare the top shelf

Source p. 3

  1. Attach the shelf ends and orient the finished edge toward the front. Fix the shelf onto the post tops and fit its supporting braces. Keep the finished particleboard edge at the front and seal any freshly cut edges that will remain exposed.
Before moving onThe shelf is level without an unsupported edge.
Stage 4 of 5

Install the hanging rods

Source p. 3

  1. Drill through the center support as required but only partway into the outer posts. Fit the full rail below the shelf and the half rail at the lower source height. Mark the blind-hole depths separately from the through-hole in the middle post so the outer visible faces remain intact.
Before moving onRods seat at both ends and cannot slide out.
Stage 5 of 5

Finish and assess stability

Source p. 3

  1. Fill and smooth recessed fasteners and finish the exposed surfaces. Keep heavy items low and provide restraint if the intended loading or location makes the rack prone to tipping. Check stability with garments concentrated on one side as well as evenly distributed, since real use rarely loads the rack symmetrically.
Before moving onThe rack remains stable with the intended garments.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Clothes Rack.pdf
Source length
3 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.