Project library / Tables & desks

Tables & desks / Build companion

Mission Spindle Coffee Table

A Mission-style coffee table has five vertical spindles at each end and a pegged low center stretcher.

Advanced6 stages5-page source
AI finished-project concept for Mission Spindle Coffee Table
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. An original study guide based on the supplied historical plan; not shop-tested. Use the privately owned source drawings for full-size patterns and complete cutting details.
Understand the project

What makes this build.

The five-spindle end frames, three stretcher connections and pinned through tenons require accurate mortise layout from several drawing sheets.

Five flat spindles fill each short end.

The lower center stretcher has exposed chamfered tenons.

Shallow curves lighten the long upper rails and lower stretcher.

Points to resolve before building

  • These are dimensioned drawings, not a supplied written assembly procedure; retain all five sheets.
  • The stated overall height and component stack should be reconciled in the shop layout before final cutting.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw
  • Router or mortising tools
  • Chisels
  • Drill
  • Clamps
  • Sander

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Stated overall size18 in high × 36 in wide × 22 in deepSource p. 1
Top¾ × 22 × 36 inSource p. 2
End spindlesTen total; ⅞ in wide × ¼ in thickSource p. 3
Leg section1¾ in squareSource p. 5

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 6

Reconcile the five drawing sheets

Source pp. 1, 2, 3, 4, 5

  1. Make a parts list from the top, spindle, stretcher and leg sheets before cutting. Keep reference dimensions distinct from the dimensions controlling joint shoulders. Compare the overall height with the leg length and top thickness in the drawings, resolving the small discrepancy in one consistent shop layout.
Before moving onThe complete dry-layout dimensions agree.
Stage 2 of 6

Mortise the square legs

Source p. 5

  1. Mark inward faces and cut the upper and lower mortises from the leg sheet. Leave the inner foot bevels until the joint references are established. The mortises are offset from the outer faces to create a consistent rail setback; use that face reference on every leg.
Before moving onAll paired mortises share the same heights and setbacks.
Stage 3 of 6

Build the spindle ends

Source p. 3

  1. Cut matching upper and lower end rails and mortise them for five slender spindles per end. Fit the spindle tenons and dry-assemble each end before gluing. The slender spindle tenons require gentle fitting, so pare the mortises rather than bending the spindles into a misaligned rail pair.
Before moving onSpindle spacing is even and both end frames are square.
Stage 4 of 6

Fit the long stretchers

Source p. 4

  1. Cut the shallow lower-edge curves and fit the upper rail tenons into the legs. Fit the lower center stretcher through the end rails with its chamfered ends projecting as shown. The bottom stretcher differs in thickness from the two upper stretchers, and its through tenons have a different fit and projection.
Before moving onThe base remains square and the exposed tenons project equally.
Stage 5 of 6

Peg and assemble the base

Source pp. 3, 4, 5

  1. Assemble the matched end frames and stretchers in a planned clamping sequence. Fit the lower-stretcher retaining pegs through the underside of the end rails as indicated. Confirm the retaining-peg path in the dry assembly so it crosses the tenon without emerging through a visible face unexpectedly.
Before moving onThe lower stretcher cannot withdraw and the feet share a plane.
Stage 6 of 6

Shape and attach the top

Source p. 2

  1. Prepare the solid or edged-veneer top and form the illustrated cove-like underside edge. Attach with Z clips or equivalent suitable fittings that permit solid-wood movement. If choosing a veneered substrate, adapt the edge profile to its banding thickness rather than exposing the core under the cove.
Before moving onThe top is centered and securely retained with movement allowance.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Coffee Table 1.pdf
Source length
5 pages
Attribution
Philip Bumbalough, BenchMark, Mission Style Coffee Table, December 10, 2002, revision A.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.