Project library / Tables & desks

Tables & desks / Build companion

Tongue-and-Groove Coffee Table

A low redwood table frames a boarded top above laminated corner legs and concealed cross braces.

Intermediate5 stages1-page source
AI finished-project concept for Tongue-and-Groove Coffee Table
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. An original study guide based on the supplied historical plan; not shop-tested. Use the privately owned source drawings for full-size patterns and complete cutting details.
Understand the project

What makes this build.

Layered corner legs and a framed tongue-and-groove top need accurate square assembly and an explicit wood-movement strategy.

Laminated board corners form substantial legs.

A deep perimeter frame surrounds the top boards.

Two concealed cross braces support the long top.

Points to resolve before building

  • Review seasonal movement before reproducing the source’s multiple nailed top connections.
  • The low table is not a verified seat or platform.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw
  • Drill
  • Square
  • Band clamps
  • Sander

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Top-board blanksFour at ¾ × 5½ × 52½ inSource p. 1
Side-frame piecesTwo at ¾ × 5½ × 54 inSource p. 1

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Prepare the layered legs

Source p. 1

  1. Cut the inner and outer leg pieces from the single-page schedule. Assemble the inner pairs with their top supports flush to the upper ends. Label inner and outer leg pieces before assembly because their different lengths establish the support height beneath the framed top.
Before moving onBoth end assemblies match.
Stage 2 of 5

Wrap the outer leg faces

Source p. 1

  1. Fit the outer leg boards around the inner pieces. Use a square temporary block and band clamps to keep the corners true during glue-up. The temporary square block is an assembly aid, not a permanent filler; remove it before the glue can bond it inside the leg.
Before moving onAll four corner legs have square closed seams.
Stage 3 of 5

Fit the perimeter frame

Source p. 1

  1. Attach the long side-frame pieces and then the end pieces. Check the rectangle before fitting the boarded top. Keep the top of the perimeter frame aligned with the intended board surface so the finished top has no raised lip.
Before moving onThe frame diagonals agree.
Stage 4 of 5

Fit the tongue-and-groove top

Source p. 1

  1. Split one top board to form the two edge pieces and fit the full boards between them. Adapt fastening to allow expected solid-wood movement instead of rigidly trapping the complete panel. Fit both narrow edge strips last, using their actual remaining width rather than assuming the first rip divides the board exactly in half.
Before moving onBoards fit without forcing the perimeter apart.
Stage 5 of 5

Brace and finish

Source p. 1

  1. Fit the underside cross braces and their corner reinforcement. Recess fasteners, ease edges and apply a finish appropriate to the intended location. Locate the cross braces below solid bearing areas and avoid fasteners that can protrude through the thin top boards.
Before moving onThe top is supported and the base does not rack.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Coffee Table -1.pdf
Source length
1 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.