Project library / Tables & desks

Tables & desks / Build companion

Shaker Console Table

A narrow cherry console with four tapered legs, a chamfered top and traditional mortise-and-tenon aprons.

Intermediate5 stages6-page source
AI finished-project concept for Shaker Console Table
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. Original guide to an archival plan; not shop-tested. Check the source drawings and actual material sizes before cutting.
Understand the project

What makes this build.

Two-face leg tapers and meeting mortise-and-tenon joints demand careful orientation.

Two-face leg tapers and meeting mortise-and-tenon joints demand careful orientation.

The drawing uses a one-inch top overhang on every side.

Points to resolve before building

  • Keep tapered leg faces correctly oriented; rigidly fixing the solid top can cause splitting.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw
  • Hand plane
  • Drill
  • Mortise chisels
  • Clamps

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Overall48 in long × 18 in deep × 29 in highSource p. 1
Top13/16 × 18 × 48 inSource p. 1

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Prepare the stock

Source pp. 2, 3

  1. Choose straight cherry for the top and rails and arrange three laminations per leg. Glue the legs and edge-joint the top with the grain arranged deliberately. Keep the three leg laminations flush during clamping, then let the adhesive fully cure before cutting the joints.
Before moving onLaminations cure straight and the top can be flattened.
Stage 2 of 5

Lay out the mortises

Source pp. 3, 4

  1. Mark the two adjoining inside faces of each leg and transfer the rail heights from a common reference. Bore and chisel the mortises before tapering. Leave enough wood between the adjoining mortises and label the rail that will fit each opening.
Before moving onJoint locations match corresponding apron ends.
Stage 3 of 5

Fit the apron tenons

Source pp. 4, 5

  1. Saw the shoulders and cheeks, then pare to a close hand fit. Dry-assemble the four rails and legs and check the top overhang. Keep the marking gauge registered to the same face so the apron shoulders align around all four corners.
Before moving onShoulders close without forcing the frame out of square.
Stage 4 of 5

Taper and assemble the base

Source pp. 5, 6

  1. Taper only the two inner faces below the apron area. Glue the long side assemblies first, then connect them with the end rails while comparing diagonals. Plane the sawn tapers to the lines and pre-sand the inside faces while they are still easily accessible.
Before moving onFour feet sit evenly and the frame is square.
Stage 5 of 5

Finish and attach the top

Source pp. 1, 6

  1. Plane the top flat and chamfer its four edges. Fit the metal clips into the apron slots and secure the top with room to move across its grain. Use a backing block when planing end-grain chamfers, then center the base on the padded inverted top.
Before moving onTop overhang is balanced and clips can accommodate movement.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Console Table.pdf
Source length
6 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.