Project library / Storage & cabinets

Storage & cabinets / Build companion

Corner Computer Cabinet

A tall oak-faced corner workcenter combining a triangular desk with open upper storage.

Advanced5 stages6-page source
AI finished-project concept for Corner Computer Cabinet
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. Original guide to an archival plan; not shop-tested. Check the source drawings and actual material sizes before cutting.
Understand the project

What makes this build.

Angled face framing must align with a square-backed triangular case.

Angled face framing must align with a square-backed triangular case.

The desktop and shelf have rear cable clearances.

Points to resolve before building

  • Locate concealed services before wall fastening and check ventilation for enclosed equipment.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Guided circular saw or table saw
  • Jigsaw
  • Drill
  • Clamps
  • Level

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Back panel height66 inSource p. 2
Side panels¾ × 10 × 66 inSource p. 2
Top and desk rough panels38¼-in square before corner shapingSource p. 2

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Map the corner footprint

Source pp. 2, 3

  1. Draw the full-size diagonal front and check the room corner, baseboard and intended equipment. Transfer the actual panel geometry before cutting the triangular parts. The unequal back widths account for their overlap, so they must not be replaced with two identical panels.
Before moving onThe cabinet fits the room and the seated work position.
Stage 2 of 5

Prepare the panels

Source pp. 3, 4

  1. Cut the two overlapping backs, sides and horizontal panels. Clip the rear corners of the desktop and shelf for cable passage as shown, leaving the top intact. Fit the cable organizer before closing access to the rear corner, and keep fasteners out of the cable route.
Before moving onEach horizontal panel fits between its intended supports.
Stage 3 of 5

Assemble the right-angle shell

Source pp. 3, 4

  1. Join the backs at ninety degrees, then install the supporting cleats and shelves. Fit the beveled sides while keeping the whole case square. Dry-position the horizontal panels on their cleats to verify that the left and right supports are level together.
Before moving onBoth backs remain perpendicular and shelves are level.
Stage 4 of 5

Fit the diagonal face

Source pp. 4, 5

  1. Cut the front stiles to the specified beveled edges and fit the rails and shelf edging to the actual assembly. Add the decorative top trim only after the frame closes cleanly. Use scrap test cuts to check the diagonal front joints before trimming the finished oak stiles and edging.
Before moving onMiters meet and the openings remain unobstructed.
Stage 5 of 5

Install and secure

Source pp. 5, 6

  1. Level the cabinet with shims and fasten it to suitable wall structure. Fit any keyboard tray and cable opening to current equipment and protect cords from sharp panel edges. Check drawer or tray travel with the cabinet in its final position, including access past the diagonal face.
Before moving onCabinet cannot tip and cables do not snag moving hardware.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Corner Cabinet 1.pdf
Source length
6 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.