Project library / Tables & desks

Tables & desks / Build companion

Mahogany Drop-Leaf Table

A tapered-leg mahogany table with rounded drop leaves held by folding wooden supports.

Advanced5 stages3-page source
AI finished-project concept for Mahogany Drop-Leaf Table
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. Original guide to an archival plan; not shop-tested. Check the source drawings and actual material sizes before cutting.
Understand the project

What makes this build.

Hinge mortises and folding support geometry must work together.

Hinge mortises and folding support geometry must work together.

The outer leaf corners have a generous rounded profile.

Points to resolve before building

  • Do not load a raised leaf until its supports are fully engaged.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw
  • Bandsaw
  • Router
  • Drill
  • Chisels
  • Clamps

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Leaf corner radius4 inSource p. 2
Support pivot dowel¼-in diameterSource p. 2

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Prepare the top panels

Source p. 1

  1. Glue up the center and two leaves with grain and color aligned. Keep the three panels flat and equal in thickness. Mark the original order and show faces so the grain remains coordinated when the leaves are hinged beside the center.
Before moving onLeaf edges meet the center cleanly.
Stage 2 of 5

Build the base

Source pp. 1, 2

  1. Fit the apron mortises and tenons, add the lower bead and clip grooves, then taper only the two inside leg faces below the apron. Leave the outside leg faces straight, and confirm the clip grooves remain accessible after the frame has been glued.
Before moving onFrame dry-fits square.
Stage 3 of 5

Fit the leaf hinges

Source p. 2

  1. Lay out two hinges per leaf with the source spacing and a controlled gap. Recess them cleanly and test the leaf swing before rounding its outer corners. Check the hinge axis against the panel edges on scrap before routing the finished leaves; a misplaced axis can make them bind.
Before moving onLeaves rise level and fold without binding.
Stage 4 of 5

Make folding supports

Source p. 2

  1. Form the interlocking wooden knuckles and dowel pivots, or fit suitable hinges as the source permits. Notch for hinge barrels and verify the support sweep. Test that each support folds fully inside the apron and swings far enough beneath its leaf to provide the intended bearing.
Before moving onSupports hold each leaf level and fold clear.
Stage 5 of 5

Finish and attach

Source pp. 2, 3

  1. Finish accessible pieces separately, then install supports and attach the top with clips allowing cross-grain movement. Test both leaves on the completed base. Check hinge screws and supports with each leaf lowered and raised, including clearance between the folded mechanisms and the legs.
Before moving onNo leaf drops from an incompletely engaged support.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Drop leaf table.pdf
Source length
3 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.