Project library / Workshop

Workshop / Build companion

Adjustable Finishing Easel

A pair of sliding uprights converts a suitable sawhorse into a support for finishing doors and panels.

Intermediate5 stages1-page source
AI finished-project concept for Adjustable Finishing Easel
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. Original guide to an archival plan; not shop-tested. Check the source drawings and actual material sizes before cutting.
Understand the project

What makes this build.

The notch geometry must fit the actual sawhorse.

The notch geometry must fit the actual sawhorse.

One upright slides on two dowels to suit different panel widths.

Points to resolve before building

  • The source gives no load rating; tall or heavy panels can overturn an unsuitable sawhorse.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw
  • Jigsaw
  • Drill
  • Clamps

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Use the original drawing.

The source does not provide a complete, confidently readable set of dimensions here. Confirm the original drawing and develop a measured parts list before cutting.

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Fit the sawhorse

Source p. 1

  1. Measure the actual horse and add the stretcher shown in the drawing. Lay out the lower rectangular notch and upper angled notch from that geometry. The notches must fit the particular sawhorse, since the stretcher location and upper contact determine the easel’s working angle.
Before moving onUprights seat fully on the horse.
Stage 2 of 5

Cut the matching uprights

Source p. 1

  1. Cut both profiles and drill the connecting dowel holes at matching heights. Clamp the uprights together for layout so the dowels pass straight through both without forcing the sliding member out of alignment.
Before moving onThe supports share one slope.
Stage 3 of 5

Make the sliding connection

Source p. 1

  1. Glue and screw both long dowels into one upright while leaving the second free to slide. Test adjustment over the useful width range before securing the fixed ends; glue on the moving upright would defeat the adjustment.
Before moving onWidth adjusts without the uprights tipping.
Stage 4 of 5

Add work supports

Source p. 1

  1. Fit short front pegs and smooth contact covers. Use a securely restrained method to split the PVC rather than feeding loose round pipe into a saw. Keep the peg projections equal and the cover fasteners recessed so neither can scratch a finished face or catch the workpiece.
Before moving onNo sharp contact edges remain.
Stage 5 of 5

Test before finishing

Source p. 1

  1. Place a representative dry panel on the easel and check the sawhorse stance, balance and support spread. Secure the panel if necessary before coating it. The easel and horse must remain stable with the intended panel in place; adjust their position before opening the finish container.
Before moving onAssembly is stable under the intended load.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Finishing Easel.pdf
Source length
1 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.