Project library / Storage & cabinets

Storage & cabinets / Build companion

Fishing Rod Rack

A freestanding pine rack with seven rod notches and side pegs for reels.

Intermediate5 stages1-page source
AI finished-project concept for Fishing Rod Rack
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. Original guide to an archival plan; not shop-tested. Check the source drawings and actual material sizes before cutting.
Understand the project

What makes this build.

Accurately spaced holes and a straight splitting cut are needed to make the two matching rod-support rails.

A single drilled board makes two accurately matched rod rails.

Twenty side pegs add reel storage.

Points to resolve before building

  • Check the loaded rack for tipping and secure it if stored where it may be bumped.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Handsaw
  • Drill and hole saw
  • Square
  • Sander

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Sides140 × 19 × 1000 mmSource p. 1
Rail blank140 × 19 × 550 mmSource p. 1
Rod openingsSeven 50-mm holes split into paired semicirclesSource p. 1

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Mark the sides

Source p. 1

  1. Bevel the top corners and lay out paired rows of reel-peg holes at the listed stations. Drill blind holes to controlled depth. Label the inward-facing sides before boring so the twenty reel pegs face into the rack rather than toward its outside edges.
Before moving onOpposite side layouts match.
Stage 2 of 5

Make paired notched rails

Source p. 1

  1. Bore seven holes along the rail blank centerline, then saw through the centers with the offcut supported. Smooth the resulting semicircles. Mark the wider half as the upper rail and the narrower half as the lower rail immediately after separating them.
Before moving onBoth rails retain matching notches.
Stage 3 of 5

Fit feet and base

Source p. 1

  1. Bevel the front of each foot and screw it to a side. Install the sloped base using the rail as a spacing gauge. Keep each foot flush with its side’s rear edge, and use the loose rail to maintain equal spacing during base attachment.
Before moving onThe assembly stands square.
Stage 4 of 5

Install rails and pegs

Source p. 1

  1. Fit the wider rail near the top rear and the narrower one lower at the front, then glue in the reel pegs. Check the upper and lower rod notches align and the rack stands square before the glued dowels are installed permanently.
Before moving onRod positions align and pegs are secure.
Stage 5 of 5

Finish the rack

Source p. 1

  1. Fill and sand fastener holes, apply the desired finish and line the semicircles with felt after curing. Test the cured rack with actual rod handles and reels, checking the felt protects the finish and the pegs do not crowd neighboring equipment.
Before moving onNo rough edges touch rod finishes.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Fishing Rod Holder.pdf
Source length
1 pages
Attribution
Dieter Mylius, Let’s Go Fishing rod rack article.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.