Project library / Boxes & small projects

Boxes & small projects / Build companion

Maple Music Box

A birdseye-maple music box with dark molded trim, small bracket feet and a mirrored hinged lid.

Intermediate5 stages5-page source
AI finished-project concept for Maple Music Box
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. Original guide to an archival plan; not shop-tested. Check the source drawings and actual material sizes before cutting.
Understand the project

What makes this build.

Small mitered moldings and two-piece bracket feet demand accurate supported cuts.

Small mitered moldings and two-piece bracket feet demand accurate supported cuts.

The mirror faces the listener when the hinged lid is open.

Points to resolve before building

  • Source cove-cutter descriptions conflict; verify the profile before routing. Movement hole dimensions depend on the actual purchased mechanism.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw with accurate miter support
  • Router table
  • Drill
  • Clamps
  • Sander

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Box side stock½ × 2¼ × 9 in fronts/backs; ½ × 2¼ × 5 in endsSource p. 3

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Choose the movement first

Source pp. 2, 3, 5

  1. Place the actual mechanism on a full-size base layout and mark its fasteners and winding-key clearance. Compare the lid, mirror and hinge requirements before cutting the case, since replacement movements may differ from the archived example.
Before moving onThe selected mechanism fits with operating clearance.
Stage 2 of 5

Shape the trim while it is long

Source pp. 3, 4

  1. Prepare the top and base molding profiles on long stock with supported, guarded setups, then miter the finished strips to length. Reconcile the conflicting cove-bit descriptions against the desired profile instead of selecting a cutter from the text alone.
Before moving onMolding miters close and the panel groove matches its panel.
Stage 3 of 5

Make the case and bracket feet

Source pp. 4, 5

  1. Miter the maple sides and ends, dry-fit them around the base and glue the box square with a band clamp. Shape foot stock before dividing it into the small mitered pieces, then assemble each pair into a corner bracket.
Before moving onThe box is square and all four feet sit evenly.
Stage 4 of 5

Fit the base and lid assemblies

Source pp. 4, 5

  1. Fit the lower molded frame around the base and position the bracket feet beneath it. Assemble the molded lid around its panel, then test the hinges and lid clearance before fastening the base permanently.
Before moving onLid closes evenly without binding on the molding.
Stage 5 of 5

Finish and install the music hardware

Source p. 5

  1. Finish the contrasting woods before mounting the movement and mirror, masking glue areas where needed. Bore the winding-key opening from the actual mechanism layout, use mirror-compatible adhesive, and test the music with the lid open and closed.
Before moving onThe key operates freely and mirror and mechanism are secure.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Music Box.pdf
Source length
5 pages
Attribution
Rockler, Music Box Plan, archived October 2004.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.