Project library / Tables & desks

Tables & desks / Build companion

Cherry Nesting Tables

Three slender cherry nesting tables with veneered rails, tapered legs and a shaped largest top.

Advanced6 stages11-page source
AI finished-project concept for Cherry Nesting Tables
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. Original guide to an archival plan; not shop-tested. Check the source drawings and actual material sizes before cutting.
Understand the project

What makes this build.

Four-face leg tapers, veneered rails and three interdependent frames require careful coordination.

Four-face leg tapers, veneered rails and three interdependent frames require careful coordination.

Only the smallest table has a front rail; the larger two remain open for nesting.

The largest top has a curved outline while the smaller tops remain simpler.

Points to resolve before building

  • Use a supported tapering method and feed against cutter rotation; omit the unsafe historical jointer and climb-cut suggestions.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw
  • Bandsaw or supported tapering jig
  • Hand plane
  • Router
  • Dowel or biscuit jig
  • Clamps

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Largest top blank¾ × 14¾ × 20 inSource p. 3
Middle top blank¾ × 13½ × 14½ inSource p. 3
Smallest top blank¾ × 12½ × 11½ inSource p. 3
Leg lengths20¼, 19⅛ and 18 in for large, middle and small tablesSource p. 3

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 6

Prepare three coordinated sets

Source pp. 3, 4

  1. Label every leg and rail by table size and position before machining. Glue and flatten the solid top stock, reserving the largest blank for its shaped perimeter, and confirm the three planned frames leave nesting clearance.
Before moving onParts are grouped correctly and the nesting layout clears.
Stage 2 of 6

Taper the matching legs

Source pp. 5, 6

  1. Lay out the long lower tapers on all four faces while retaining square joint areas above. Use a supported saw jig or bandsaw followed by hand planing; do not copy the source’s unsupported jointer drop-cut technique.
Before moving onAll four legs in each set match and stand at equal height.
Stage 3 of 6

Veneer and shape the rails

Source pp. 6, 7, 8

  1. Bond the decorative veneer to prepared flat rail faces using the selected adhesive instructions. Trim with a supported method, then form the shaped lower edge on the smallest table’s front rail from the private source pattern.
Before moving onVeneer remains intact and the front-rail curve is smooth.
Stage 4 of 6

Fit the frames

Source pp. 8, 9

  1. Fit the chosen dowel or biscuit joints with the rails set back consistently from the leg faces. Dry-assemble the largest and middle frames with their front openings unobstructed, then check the smaller tables slide through before glue-up.
Before moving onThe three dry frames nest without rubbing or racking.
Stage 5 of 6

Shape and attach the tops

Source pp. 9, 10

  1. Cut the largest top’s curved outline and form the underside edge treatment on front and sides, retaining the plain rear edge. Fit each top with movement-permitting fasteners; do not restrain the solid panel rigidly across its grain.
Before moving onTops overhang consistently and remain free to move seasonally.
Stage 6 of 6

Finish and test the set

Source pp. 10, 11

  1. Sand the veneer gently so its figured face is not cut through, and finish the tables separately. After curing, nest and separate them repeatedly while checking top edges, rail clearances and the stance of every table.
Before moving onAll three tables slide freely and stand without rocking.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Nesting Tables.pdf
Source length
11 pages
Attribution
Collection copyright 2004 Martian Auctions; original authorship unverified
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.