Project library / Boxes & small projects

Boxes & small projects / Build companion

Wall Paper Towel Holder

A pine wall holder with rounded side brackets and a removable spring-ended wooden roll spindle.

Intermediate5 stages6-page source
AI finished-project concept for Wall Paper Towel Holder
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. Original guide to an archival plan; verify the conflicting overall-width statement and spindle-pin typo against the illustrated assembly and actual roll. Not shop-tested.
Understand the project

What makes this build.

The spring-ended spindle needs enough travel for removal and enough engagement for retention.

The spring-ended spindle needs enough travel for removal and enough engagement for retention.

The sides fit outside the back board; the cover’s overall-width claim conflicts with that drawing.

Points to resolve before building

  • Check the printed pin-length typo and the width discrepancy against the actual assembly. Retain the spring and pin securely; do not leave small loose parts.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw or jigsaw
  • Drill with depth stop
  • Clamps
  • Sander

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Back board¾ × 6 × 13 inSource p. 3
Side blanksTwo, ¾ × 6 × 6 inSource p. 3
Rounded front corners1½-in radiusSource p. 3

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Check the roll and overall layout

Source pp. 1, 2, 3

  1. Measure the intended towel roll against the back and side projection. The drawing places the sides outside the 13-in back, so verify the assembled width rather than using the conflicting 13-in overall-width claim.
Before moving onThe actual roll clears the back and both brackets.
Stage 2 of 5

Make matching side brackets

Source p. 3

  1. Cut the two side blanks together or from one accurate template, then round the two front corners on each. Mark the spindle sockets as mirrored inside faces and drill with a depth stop so the shallow holes do not break through.
Before moving onBoth brackets match and their socket centers align.
Stage 3 of 5

Join the back and brackets

Source pp. 2, 3

  1. Dry-fit the side-to-back joints with dowels or the source’s screw-and-plug alternative. Clamp the assembly square and measure the clear span between sides before committing to the spindle length.
Before moving onThe sides are parallel and the measured span is recorded.
Stage 4 of 5

Fit the removable spindle

Source pp. 4, 5

  1. Bore the spindle ends for the fixed pin and the deeper spring-pin assembly, using the actual parts to establish travel. Test insertion and removal before final retention so the spring pin extends fully into its bracket socket and cannot fall free during use.
Before moving onThe spindle installs easily and both pins remain engaged.
Stage 5 of 5

Finish and mount the holder

Source pp. 5, 6

  1. Ease the edges, finish the wood and let it cure before reinstalling the spindle. Use mounting fasteners suited to the actual wall or cabinet, then test a full roll, repeated changes and a normal downward pull.
Before moving onHolder remains secure and the roll turns without rubbing.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Paper Towel Holder.pdf
Source length
6 pages
Attribution
Knotty Plans, Paper Towel Holder, plan 03-400, copyright 2003.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.