Project library / Tables & desks

Tables & desks / Build companion

Burl Parsons Table

A compact white-oak Parsons table with mitered leg-and-rail frames and a balanced burl-veneered top.

Advanced5 stages3-page source
AI finished-project concept for Burl Parsons Table
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. Original guide to an archival plan; not shop-tested. Check the source drawings and actual material sizes before cutting.
Understand the project

What makes this build.

The mitered corners conceal paired tenons and demand accurate fitted joinery.

The mitered corners conceal paired tenons and demand accurate fitted joinery.

Veneer on both faces balances the plywood tabletop.

Points to resolve before building

  • Use securely supported joinery setups; the archive’s homemade saw jig is not a substitute for checking the actual machine clearances and guarding.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Saw with supported joinery jigs
  • Mortising tools
  • Router or rabbet plane
  • Veneer press or cauls
  • Drill
  • Clamps

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Overall drawing32 in long × 24 in wide × 20 in highSource p. 2
Top core¾ × 20½ × 30¼ inSource p. 1

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Prepare the frame and top blanks

Source pp. 1, 3

  1. Mill the white-oak legs and long rails to matching square sections, keeping each leg-and-rail pair labeled. Cut the plywood core oversize for veneering and arrange the figured face so its pattern reads across the whole top.
Before moving onFrame stock matches and the veneer layout is intentional.
Stage 2 of 5

Fit the mitered frame joints

Source pp. 2, 3

  1. Use the private schematic to lay out the double tenons in the rail ends and mating mortises in the mitered leg tops. Prove the supported cutting setup on scrap, then fit one joint at a time without weakening the narrow cheeks.
Before moving onEach miter closes while both tenons seat fully.
Stage 3 of 5

Assemble the two U-shaped frames

Source pp. 2, 3

  1. Dry-fit each long rail between its two legs and compare the completed frames on a flat surface. Glue only after checking equal height, closed miters and square leg alignment, supporting the joints so clamping does not slide them apart.
Before moving onBoth frames stand square and match in height.
Stage 4 of 5

Veneer and edge the top

Source pp. 2, 3

  1. Bond the decorative face and balancing back veneer using a suitable pressing method, then trim the cured panel to size. Fit the rabbeted side stretchers to the actual panel thickness so the finished top meets the surrounding frame cleanly.
Before moving onThe panel is flat and its edge joints close.
Stage 5 of 5

Join and finish the table

Source pp. 2, 3

  1. Fit the concealed cleats and screw the top/stretcher assembly to the two leg frames as shown in the schematic. Check the table for twist and rocking before final sanding, then apply a compatible clear finish that preserves the burl figure.
Before moving onThe top is flush, the joints are tight and all four legs bear evenly.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Parsons Table.pdf
Source length
3 pages
Attribution
Woodworker’s Journal, Vol. 10 Issue 3, May–June 1986, project 18173EZ.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.