Project library / Garden & outdoor

Garden & outdoor / Build companion

Painted Window Box

A simple painted plywood flower box with an optional decorative cutout motif.

Beginner5 stages2-page source
AI finished-project concept for Painted Window Box
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. Original reading guide based on the archived plan; not shop-tested. Confirm diagram dimensions against the private source before cutting.
Understand the project

What makes this build.

Straight plywood panels make a simple box, with particular attention needed at its weatherproofing and mounting.

A basic five-panel box can be sized to a liner.

Painted cutout decorations are optional.

Points to resolve before building

  • Wet soil is heavy; mounting details require site-specific selection.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Jigsaw or saw with plywood blade
  • Drill
  • Sander
  • Clamps

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Long panel length30 inSource p. 2
Nominal panel width8 in; allow for saw kerf and actual fitSource p. 2

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Size around the liner

Source p. 2

  1. Choose the location and any liner first. Lay out the long panels while allowing for saw kerf rather than assuming three full-width strips emerge from the sheet. Choose a removable liner before setting the box length, leaving room to lift it out without dragging it against the walls.
Before moving onThe cut layout fits the real panel.
Stage 2 of 5

Assemble the long U-section

Source p. 2

  1. Join the front and back to the bottom with suitable exterior adhesive and fasteners. Check both ends for square before closing the box. Clamp a straight batten along the long plywood edge during assembly to prevent a bowed wall from following an uneven bottom.
Before moving onThe long assembly is straight.
Stage 3 of 5

Fit the end panels

Source p. 2

  1. Measure the actual opening between the long sides and fit both ends. Fasten through sides and bottom without splitting the plywood edges. Fit the end panels to the assembled U-section rather than forcing an oversized end that spreads the thin plywood sides.
Before moving onEnd panels fit without spreading the box.
Stage 4 of 5

Provide drainage and finish

Source p. 2

  1. Drill evenly spaced drain holes and soften all exposed edges. Seal and paint the box, including the edges most exposed to water. Seal plywood end grain carefully and make sure the finish or liner cannot block the drain openings after the box is filled.
Before moving onDrain holes remain open after finishing.
Stage 5 of 5

Plan secure placement

Source p. 2

  1. Use brackets and anchors suited to the supporting structure and fully wet contents. Avoid relying on thin siding alone for support. Consider the weight of saturated soil and standing water when selecting brackets; attachment to decorative trim alone is not a support design.
Before moving onMounting support is verified before filling.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Plywood Window Box.pdf
Source length
2 pages
Attribution
Georgia-Pacific Simple Plywood Projects, Window Box; ©2002 Lowe’s / ©2003 Georgia-Pacific.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.