Project library / Boxes & small projects

Boxes & small projects / Build companion

Walnut Poker Box

A small hinged walnut box organizes cards, chips and dice in fitted blocks and partitions.

Intermediate5 stages2-page source
AI finished-project concept for Walnut Poker Box
AI concept visualization · Use the source dimensions and fitted parts for construction.
A companion to the original plan. Original reading guide based on the archived plan; not shop-tested. Confirm diagram dimensions against the private source before cutting.
Understand the project

What makes this build.

Mitered molding, a floating bottom and fitted internal storage require precise small-box joinery.

Profiled molding supplies much of the box detail.

A floating bottom accommodates movement.

Removable fitted blocks organize gaming pieces.

Points to resolve before building

  • The source material table has a front/back quantity ambiguity; confirm the two pieces in its drawing.
Prepare the workbench

Materials & tools.

Check what you have, then confirm stock sizes and hardware against your chosen dimensions.

Materials checklist

Tools & operations

  • Miter saw or miter box
  • Router or chisel
  • Drill with 1-inch bit
  • Web clamp

Tool choices may include practical editorial suggestions. Use workholding and guarding appropriate to the actual machine and operation.

Choose dry, sound stock and test unfamiliar joints in scrap. Keep guards, push aids, eye protection, and dust control appropriate to the work.

Keep the numbers close

Measurements to know.

Selected dimensions verified from the source. This is not an automatically scaled cutting list.

Source dimensions
Lid¾ × 7⅝ × 9¼ inSource p. 2
Bottom¼ × 6⅜ × 7⅞ inSource p. 2

Printed diagrams and concept images are not scale references. Verify measurements, material thickness, hardware fit, and allowances before cutting.

Inches to millimeters

Convert a measurement without changing the design. Enter a decimal or a fraction, such as 1 3/8.

34.925 mm

Nominal lumber names and actual finished sizes are different. Converting units does not choose a substitute stock size.

From stock to finished project

Let’s make it.

Read the complete sequence before cutting. Mark a stage complete after its fit checks and any required glue cure.

Stage 1 of 5

Fit molding to the contents

Source p. 1

  1. Confirm cards and chip sizes, then cut the profiled walnut sides with matched miters. Check the bottom groove in the actual molding. Lay out the actual chips, cards and dice inside a paper footprint first, including finger access for removing each item.
Before moving onThe chosen contents fit the planned interior.
Stage 2 of 5

Machine internal grooves

Source p. 1

  1. Lay out the partition grooves before assembling the shell. Keep the shallower divider slots distinct from the deeper slots in the outer walls. Test both the floating-bottom groove and any divider slots with the actual stock, keeping their locations clear of the hinge screws.
Before moving onPartitions dry-fit without binding.
Stage 3 of 5

Shape the storage blocks

Source p. 1

  1. Drill the chip recesses before trimming the block to its final outline. Prepare the card and dice blocks from the source layout and test them with real contents. Use a sample chip stack to check the shaped recess before repeating it, since chip sizes and counts vary between sets.
Before moving onEach item can be removed easily.
Stage 4 of 5

Glue the shell

Source p. 2

  1. Assemble the mitered walls around the bottom using a web clamp. Keep the bottom free to move in its groove rather than gluing it across its width. Dry-clamp all four miters around the bottom and compare diagonals; an out-of-square shell makes the lid much harder to fit.
Before moving onMiters close and the shell stays square.
Stage 5 of 5

Fit lid and dividers

Source p. 2

  1. Install the partitions after the shell cures, then fit the recessed hinges and lid. Sand and finish the interior before final hardware installation. Fit the hinges before applying the final finish and confirm that the internal dividers cannot interfere with the closing lid.
Before moving onLid opens freely and inserts fit without force.

Progress and notes stay in this browser. Nothing is uploaded.

Trace the details

Source notes.

Original PDF
Poker Chip Box.pdf
Source length
2 pages
Attribution
Rockler, Poker Chip Box using preformed box molding.
This edition
116 Studio · Original written companion and AI concept image · November 2026

Page references count from the first page of this PDF. The original is retained in the owner’s private woodworking collection; it is not distributed by this website. Consult it for full drawings, templates, and details beyond this companion.

Historical plans can omit essential context. Source references identify where a detail came from; they do not certify the design or replace current manufacturer instructions or applicable professional review.